Construction method: 1. Keep the wall clean and dry. 2. Stick the tape on the crack and squeeze it tightly. 3. Make sure that the gap is covered with tape, then cut off the tape with a knife, and finally apply mortar. 4. Let it air dry, then lightly sand it. 5. Fill enough paint to make the surface smooth. 6. Cut off the leaked tape. Then, notice that all cracks have been properly repaired, and the surrounding area of the joints is modified with fine composite material to make it as clean as new. Glass fiber mesh cloth is based on glass fiber is woven fabric and is coated with polymer anti-emulsion coating. As a result, it has good alkali-resistance, flexibility, and high tensile strength in the warp and weft directions, and can be widely used in building interior and exterior wall insulation, waterproofing, and crack resistance. Glass fiber mesh cloth is mainly alkali-resistant glass fiber mesh cloth. It is made of medium-alkali-free glass fiber yarn (the main component is silicate and has good chemical stability). After the high-temperature heat setting treatment such as anti-alkali solution, reinforcing agent. Main performance and characteristics: 1. Good chemical stability. Alkali resistance, acid resistance, water resistance, cement erosion resistance, and other chemical corrosion resistance; strong adhesion to resin, easily soluble in styrene, etc. 2. High strength, high modulus, and lightweight. 3. Good dimensional stability, stiffness, flatness, not easy to shrink and deform, good positioning. 4. Good impact resistance. (Due to high strength and good toughness) 5, anti-mildew, insect-proof. 6. Fire prevention, heat preservation, sound insulation, and insulation. The main uses are widely used in: 1) Wall reinforcement materials (such as glass fiber wall mesh, GRC wall panels, EPS inner and outer wall insulation boards, gypsum boards, etc. 2) reinforced cement products (such as Roman columns, flues, etc.), 3) Granite, mosaic special mesh, marble back net, 4) Waterproof membrane cloth, asphalt roof waterproofing, 5) Reinforced plastic and rubber products 6) Fireboard, 7) Grinding wheelbase cloth, 8) Geogrid for highway pavement, 9) caulking tape for construction, etc.

There are five types of glass fiber tapes according to their types, and what are their uses. 1. Glass fiber thermal insulation tape is a kind of fiber tape, which has good thermal insulation, heat preservation, and anti-corrosion performance. Fiber tape is made of glass fiber roving or bulky glass fiber yarn, which is applicable For winding high-temperature pipe fittings, such as electric heating wire and cable. 2. Silicone rubber glass fiber protective heat insulation tape, which is a fiber tape made of thick silicon rubber coated on the glass fiber blank. The fiber tape can be used to wrap cables and other heating elements and plays a role in heat insulation. 3. Glass fiber anti-radiation heat-preservation and heat-insulation tape. The production of this kind of fiber tape is especially thick, which is generally thick. In addition to the above two types of performance, fiber tape has insulation and anticorrosive effects. 4. Silicone rubber self-adhesive tape. The double-sided tape made of this kind has good adhesiveness. It is designed to be self-adhesive and solidify. The fiber tape can form a water-tight insulation layer, which can prevent the penetration of oil and pollutants Internal woven layer. Different types of Fiberglass Filament tapes have different functions. Glass cloth high-temperature resistant tape is made of high-quality high-density alkali-free glass cloth, 3M double-sided tape is coated with imported silicone pressure-sensitive adhesive on one side, and processed by high temperature. The product has good temperature resistance (-50 ℃ ～ 200 ℃), strong adhesion, strong tear resistance, solvent resistance, and other characteristics. It is used for high-strength insulation such as H-class heat-resistant insulation banding, flexible circuit board, and ceramic component fixing. protection. Photoelectric die-cutting is the most heat-resistant and toughest in textile products, and can effectively absorb electrical insulation paint and resin. The binding capacity of glass cloth tape is extremely high, and it can withstand the high temperature of 200 ℃. Adhesive tape with tear resistance, good conformability, high-temperature flame retardant adhesive; used for coil encapsulation and fixation, and used as the core, outer layer, and insulation between wires; high-temperature adhesive tape can basically replace 3M-69, P212 in performance, TESA4618 and other imported glass cloth tape.

Glass fiber tape is an adhesive product made of PET film as the base material and woven with glass fiber or polyester fiber. Fiber tape manufacturers Features: plastic fiber-reinforced backing material, extremely high tensile strength, high abrasion resistance, and moisture resistance, good shape, strong tensile strength, anti-friction, high-temperature resistance, solvent resistance, insulation, flame resistance, etc. , Strong adhesion, perfect packaging effect and not easy to lose. It has a wide range of uses and many characteristics and can use the most economical portion to achieve the best packaging benefits. Thickness: 0.16 (mm) Glue: acrylic Initial adhesion:> = 10N / 25mm Holding force:> = 30 (Hrs) Elongation: 180 (%) Temperature resistance: 120 degrees Product classification: ◆ Fiber We have a single-line type, double-line type, and mesh type fiber. ◆ Glue coated with hot melt adhesive, acrylic, rubber according to different requirements ◆ Thickness can be adjusted according to the weight and material of the package. The thickness of the fiber tape can be adjusted. High temperature resistant Teflon tape ◆ Special specifications can be made into mother rolls, cut into small rolls, long rolls, and other specifications according to customer requirements. ◆ -Viscosity is divided into low-viscosity, medium-viscosity, high-viscosity, residual glue, and transfer glue according to different uses to meet the requirements of different customers. Uses: The fiber tape is used for coil packaging and fixing, as well as carton repackaging, household appliances washing machines, refrigerators, metal, and wooden furniture packaging. It can be printed on the surface, and can effectively absorb resin and electrical insulation paint. Glass fiber cloth tape has the characteristics of strong tensile force, anti-friction, high-temperature resistance, solvent resistance, insulation, and good flame resistance. Glass fiber cloth is based on imported high-density alkali-free glass fiber cloth. It is suitable for transformers, high-temperature equipment, air conditioner contractors, coil wrapping and motors, and other high-temperature special environment applications. Performance, insulation, flame resistance, and other characteristics.

The division of mesh fiber tape is mainly based on the aperture of the mesh belt The division of the outer wall grid zone is mainly based on the holes of the grid zone. It can be divided according to the number of meshes, that is, how many grids are in a square meter. The smaller the holes, the more expensive the mesh belt, so we can think that the larger the mesh number, the better the quality of the mesh belt. In addition, we can divide the grid zone according to the size of the holes, that is, the size of the holes can also be used as a basis for division. We can also choose according to our needs when selecting the mesh belt. For example, when we use it on some screens, we need to choose a relatively thin glass fiber mesh belt and use it in the insulation layer of the building's exterior wall At this time, the choice of grid zone should be slightly larger. The shaping of the large-eye mesh belt is a difficult point in the production of this alkali-resistant mesh belt, and it is also the reason why the price of this mesh belt is relatively high. In the mesh belt production process, the same shape, the smaller the eyelet specifications, the easier the shape. The large-eye mesh belt can be said to be the most difficult to shape among the mesh belt products. Ordinary mesh belts are shaped by uniformly coating a layer of glue during the production process, and drying and shaping the glue after a high-temperature baking oven. This effect and quality will be very good and can meet various needs. When the large-eye mesh belt is shaped, after one side is glued and baked, the setting effect is not satisfactory, so a second pass of gluing and baking is performed, which is equivalent to two passes of the manufacturing process and Glue and heating cost output. The styling effect will reach the ideal requirements after two treatments, but the cost will increase accordingly. PET high-temperature resistant tape The division of the outer wall grid zone is mainly based on the holes of the grid zone. It can be divided according to the number of meshes, that is, how many grids are in a square meter. The smaller the holes, the more expensive the mesh belt, so we can think that the larger the mesh number, the better the quality of the mesh belt. In addition, we can divide the grid zone according to the size of the holes, that is, the size of the holes can also be used as a basis for division. We can also choose according to our needs when selecting the mesh belt. For example, when we use it on some screens, we need to choose a relatively thin glass fiber mesh belt and use it in the insulation layer of the building's exterior wall At this time, the choice of grid zone should be slightly larger. The shaping of the large-eye mesh belt is a difficult point in the production of this alkali-resistant mesh belt, and it is also the reason why the price of this mesh belt is relatively high. In the mesh belt production process, the same shape, the smaller the eyelet specifi...

Uses: to repair drywall, gypsum board joints, cracks in various walls and other wall damage Main performance: excellent alkali resistance, durable: high tensile strength and deformation resistance, crack resistance: no deterioration, no foam: excellent self-adhesion, no prior primer coating is required, quick use and easy construction Specifications: 8 × 8.9 × 9 mesh / inch: 55-85 g / m2. Width: 25-1 000 mm: Length: 10-153 meters. Color: Usually white. Construction method: 1. Keep the walls clean and dry. 2. Apply adhesive tape to the crack and squeeze it tightly. 3． Make sure the gap is covered with tape, then cut off the excess tape with a knife, and finally apply mortar. 4． Allow it to air dry, then lightly sand it with a construction hammer. 5. Fill enough paint to smooth the wall surface. 6. Cut off the leaked tape. Then, notice that all cracks have been properly repaired, and the surroundings of the joints are trimmed with fine composite materials to make them as clean as new.

High-temperature resistant tape products are divided into stripes, grids, rubber self-adhesive, etc., used as coil packaging and fixing, and used as the core, outer layer and wire insulation, household appliances, washing machines, refrigerators, metal, and wooden furniture and other products. package. A high-temperature resistant tape can be printed on the surface, and can effectively absorb resin and electrical insulation paint. Features of glass fiber tape: plastic fiber-reinforced backing material, extremely high tensile strength, glass fiber tape has high abrasion resistance and moisture resistance, good shape, strong tensile strength, friction resistance, high-temperature resistance, solvent resistance, insulation, Fire resistance, and other characteristics, not easy to break, strong adhesion, perfect packaging effect and not easy to lose.

Heat-resistant tape Features: Excellent resistance to inflammation, feels very soft in the hand, Thin piping and narrow space are easy to construct. Skin like brittle fibers is not irritating. Organic solvents can resist weakly acidic substances. Uses: anti-inflammatory, heat preservation Prevent fire damage to various piping and equipment. Specifications: Operating temperature range: 250C ° (When using 250C ° continuity, the use time is 1 week) Non-adhesive, flammable fiber-resistant fabric. Kraft paper adhesive tape: suitable for bonding vulcanized rubber such as chloroprene and EPT with metal and plastic materials; the special adhesive for rubber used by VR-5311 has excellent cohesion; VR-5321 has excellent initial adhesion. Double-sided tape: suitable for bonding vulcanized rubber such as chloroprene and EPT with metal and plastic materials; the special adhesive used for rubber has excellent cohesive force; it has excellent initial adhesion. Masking tape for printed circuit board: It has micro-rewinding property, which is convenient for pasting operation; special adhesive is used, so it can be closely adhered to the printed circuit board without peeling and shifting during operation; using heating roller After compaction, it can exert better adhesion; it has good solder resistance and flux resistance, which can prevent the penetration of solder liquid; can be used under severe conditions without residual adhesive; bonding after pasting The change in force is small, and the peeling operation is easy.

S/N Trade Fair Exhibition Time Exhibition Address Booth Number 1 CHINA IMPORT AND EXPORT FAIR  3rd Phase May 1st-5th, 2020 Guangzhou International Conference and Exhibition Centerm,China 3.2H41-42 2 INTERPACK  DUSSELDORF May, 7th-13th, 2020 Dusseldorf exhibition center, Germany 7.0 C23 3 PACK EXPO Mexico 2020 June 2nd - 5th, 2020 Expo Santa Fe Mexico - Mexico City, Mexico 2048 4 PACK EXPO International and Healthcare Packaging EXPO 2020 November 8th-11th, 2020 McCormick Place, Chicago, IL,USA W-19009 5 IPACK-IMA 2021 May 4th-7th，2021 Milan exhibition center, Italy TBC

At present, the quality of fiber tapes on the market is uneven, and the requirements for high strength and no residue of fiber tapes are becoming higher and higher. Manufacturers are also increasing. It is important to choose fiber tape manufacturers, so what needs attention when identifying fiber tapes of? 1. Color: The fiber tape itself is mostly composed of a transparent PET polyester base film and white glass fiber yarn, coated with high-performance pressure-sensitive adhesive. 2. The overall color is white. Some manufacturers use low-quality glue for the lowest cost. The stability is not good and it is easy to age and turn yellow. 3. General fiber tape is recommended to be used for half a year, etc. It needs to be placed in a dry and ventilated room temperature environment (about 25 degrees Celsius). 4. Flat rubber surface: uneven rubber surface will cause uneven distribution of stickiness, and wrinkles and springs will appear during use. 5. Straightness of the fiber yarn: The straightness of the yarn directly affects the tensile strength of the fiber tape, which will have serious consequences for the current heavy goods packaging and strapping industry, especially the steel strapping industry.